(navigation image)
Home American Libraries | Canadian Libraries | Universal Library | Community Texts | Project Gutenberg | Children's Library | Biodiversity Heritage Library | Additional Collections
Search: Advanced Search
Anonymous User (login or join us)
Upload
See other formats

Full text of "Wearables"

No-Sew Touchscreen Gloves 



i 



Make Projects 



build, hack, tweak, share, discover, J 



No-Sew Touchscreen Gloves 



Written By: Sean Michael Ragan 



f TOOLS: 

Exacto Knife (1) 
Hammer (1) 
Paint pen (1) 
Snap anvil (1) 
Snap setter (1) 



© PARTS: 



Gloved) 

This method works best with heavier 

gloves. 

Snap fastener button (1) 

AKA "cap. " this is the rounded "dome" 

part of the snap. 

Snap fastener socket (1) 

This part is riveted to the button by the 

button's integral post. 



SUMMARY 

To make capacitive touchscreens work through gloves, you need a conductive pathway 
between the screen and your finger(s). Commercial touchscreen-friendly gloves made with 
conductive fabric at the fingertips are available, and if you're handy with a needle you can 
use special thread to sew conductive stitches into the fingertips of a glove you already own. 

If you're not handy with a needle, this no-sew "hard" method, using the button or "cap" half of 
a snap fastener, may be more your style. Depending on your skills and personal tastes, it 
may come out better- or worse-looking than the "soft" method. In any case, it will certainly 
be faster, and, applied to a nice pair of new gloves, makes for a useful gift with a personal 



© Make Projects 



www.makeprojects.com 



Page 1 of 4 



No-Sew Touchscreen Gloves 

handmade touch. You can, of course, add snaps to as many of a glove's finger- and/or 
thumb-tips as you please, which may be useful for multi-touch displays. 

The round lip of the snap socket inside the glove makes it very easy to index your fingertip 
with the "sweet spot" on the outside of the glove, and the hard, rounded surface of the button 
means the actual point of contact with the screen is small and precise. There's no "fat 
fingers" effect with these gloves, and I've found that they require almost no mental 
adjustment to go back and forth between gloves and bare fingers. Finally, I should mention 
that the brass and/or nickel these snaps are made of should pose no risk of scratching even 
the softest glass. 







• Put on the glove. 

• Hold a paint pen (or other suitable marking tool) in your free hand, and touch your gloved 
fingertip to the tip of the pen. 

• Imagine you are using a touchscreen to get the dot placement just right. 




© Make Projects 



www.makeprojects.com 



Page 2 of 4 



No-Sew Touchscreen Gloves 










Remove the glove. 

Use a sharp hobby knife to make a small slit, about 1/8" long, through the marked spot on 
the glove fingertip. 

Holding the knife with the blade "upside down," as shown, makes this a lot easier. 




Insert the snap button-post through the slit into the fingertip. 




The button needs to stay in place throughout this operation. If necessary, use a 
small piece of tape to keep it from falling out. 

Turn the glove inside-out. 

Flatten out the finger so that the button-post sticks out as far as possible. 




© Make Projects 



www.makeprojects.com 



Page 3 of 4 



No-Sew Touchscreen Gloves 




Insert a snap anvil into the inverted glove, and work it up into the fingertip until its curved 
side is centered under the snap button. 

Put a snap socket over the button post with the open side up. 

Push the socket down to expose as much of the button post as possible. 




• Position a snap setter on the button post. Carefully center the setter, and try to hold it as 
upright as possible. 

• Strike the setter firmly to set the rivet. Repeat, as necessary, until the socket is set tight 
against the button, without any "play." 

• You can see my rivet-setting skills leave something to be desired. In this case, it f^f 
doesn't really matter that much if the post sets cleanly or not, because the snap will L^J 
not actually be used as a snap, and the socket will be invisible inside the glove when it's 
turned right-side out. 

• Turn the glove right-side out, again, and you're done! 

This document was last generated on 201 2-1 1 -03 02:50:47 AM. 



© Make Projects 



www.makeprojects.com 



Page 4 of 4